ESD TILES BLUE
- ESD Wearable
- ESD Consumable
- ESD Instruments
- ESD Storage
- ESD Related SET-UP & Infrastructure
- Soldering & Rework Station
- Soldering Consumables
- Soldering Accessories
- Electric Screw Driver & Accessories
- Mobile Repairing Tools
- Cleanroom & Consumables
- Glue Dispensers & Spares
- SMT Spares & Consumables
- Ionizing Products
- Lable & Tape Dispensers
Your shopping cart is empty!
Product Description
This Product has permanent
anti-static function because it uses conductive static network at the interface
of plastic particles.
ITEM |
STANDARD |
INDEX |
Size |
SJ/T11236-2001 |
600*600mm |
610*610mm |
||
Thickness |
SJ/T11236-2001 |
2.0 mm |
Electrical Resistance |
SJ/T11236-2001 |
106 -109 Ohms |
Stating Voltage |
SJ/T11236-2001 |
IVI<100V |
Static Decay |
GJB2605-1996 |
<= 2 (Sec) |
Resistance to Wear |
SJ/T11236-2001 |
<=0.020g/Cm2 |
Fire Resistance |
SJ/T11236-2001 |
FV-0 |
Dimensional |
Stability En434 |
>=0.10% |
Rate of Damnify Heating |
SJ/T11236-2001 |
<=0.50% |
Rate
of Changing Heating |
SJ/T11236-2001 |
>=0.20% |
Rate of Changing Watering |
GB4085-83 |
<0.15% |
Residual Concavity |
SJ/T11236-2001 |
<=0.15 |
Concavity |
SJ/T11236-2001 |
<=0.30 <=0.60 |
Color Fastness |
ISO 105202 |
<=6 |
CARE AND MAINTENANCE
Clean floor by machine-scrubbing with neutral cleaner (get back to us
for the right Cleaner). Lightly
soiled floors may be damp mopped but also should be periodically
machine-scrubbed. Severe soiling or black marking can be removed with floor
cleaning machine, synthetic stripping pad and a commercial stripping solution.
Clear water rinsing is necessary after any scrubbing or stripping operation to
removed all cleaner floor maintenance should apply spray and grinding. If necessary can maintenance the surface of
Brick by conductive wax periodically.
INSTALLATION
AROINDIA Electromech - Conductive tile and
Static-Dissipative tile should be installed on sub floors that are levered
smooth and free of cracks. Residual humidity should be under 2.5% tested with
the CM Dumb test. Tiles adhesive and installation site should reach a
temperature of at least 18 C at 24 hour before installation and paste the tiles
with qualified conductive glue below 10”5 Ohm for further details
on installation method.
General Preparation and Conditioning
Read the literature concerning the product description, product
limitations, product installation, adhesive information, product maintenance
and warranty before installing the tile. All materials including recommended
adhesive are to be delivered to the installation location in its original
packaging with labels intact. DO NOT stack pallets of material as this will
cause damage. Store products in a dry area protected from the weather on a
smooth, flat, dry surface with temperatures maintained between 65º F (19º C)
and 85º F (30º C). When stacking tiles prior to and during installation, place
the tiles face-to-face and sanded back-to-sanded back to prevent the sanded
back of the tiles from being contaminated and to protect the product from
damage.
Subfloor/Substrate
Inspection and Preparation General
All subfloors/substrates must be inspected prior to installation.
All substrates must be clean, smooth, permanently dry, flat, and structurally
sound. The substrate must be free of moisture, dust, sealers, paint, & etc.
DO NOT use sweeping compounds, solvents, citrus adhesive removers, or acid
etching to clean the substrate
Adhesive Information
AROINDIA ELECTROMECH Solvent Free ESD Conductive Adhesive
AROINDIA ELECTROMECH solvent Free ESD Conductive Adhesive must be
used for the installation of AROINDIA ELECTROMECH Conductive and Static
Dissipative Solid Vinyl Tile. It is a solvent free, non-flammable, high
performance Conductive adhesive for indoor installations over porous and
non-porous substrates on grade, below grade or above grade
AROINDIA Electromech - Static Dissipative Vinyl Tile installation
should only be performed with the AROINDIA Electromech 66/67 Solvent Free ESD
Conductive Adhesive. Read all installation literature before proceeding. Prior
to adhesive application, dry lay the flooring to ensure
AROINDIA
ELECTROMECH PVT. LTD.
desired
aesthetics (refer to 6.1). Follow safety precautions on the adhesive label and
Material Safety Data Sheet. Ensure the installation area has adequate
ventilation.
Grounding
& Grounding Diagram
To ground
the conductive flooring to a known
ground, use the 1” wide
x 0.004” thick
x 18” long copper foil strips which are supplied
by ARO-AADI INTERNATIOAL. Place approximately 9” of the strip into
AROINDIA ELECTROMECH Solvent Free ESD Conductive Adhesive while the adhesive is
still wet to ensure a 100% transfer to the copper foil backing, under the tile
nearest the ground point. AROINDIA ELECTROMECHESD Adhesive must also be applied
to the top section of the copper foil strips in order to complete the
conductivity and to bond the tile to directly to the copper foil
strips. Allow the other half,
approximately 9”, of the length
of the strip to “pigtail” up the
wall to permit an electrician to mechanically connect the copper foil to the
ground point. If using a specifically supplied ESD facility grounding system, a
ground bus bar would be placed near the floor where any ESD ground can be connected.
QUALITY CONTROL
1-
Random test for the conductivity, color difference
and dimension before delivery.
2-
Test each batch of conductive
adhesive for electrical resistance before delivery.
3- AROINDIA
ELECTROMECH representatives are available to provide technical assistance in
evaluation of onsite installation condition or to review actual installation techniques.
When you order from opencartworks.com, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process.
The total time it takes to receive your order is shown below:
The total delivery time is calculated from the time your order is placed until the time it is delivered to you. Total delivery time is broken down into processing time and shipping time.
Processing time: The time it takes to prepare your item(s) to ship from our warehouse. This includes preparing your items, performing quality checks, and packing for shipment.
Shipping time: The time for your item(s) to tarvel from our warehouse to your destination.
Shipping from your local warehouse is significantly faster. Some charges may apply.
In addition, the transit time depends on where you're located and where your package comes from. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!